$14.95

Download Now
Sold by onedollar on Tradebit
The world's largest download marketplace
3,247,664 satisfied buyers
Shopper Award

Kyocera KM-4800w, Service Manual

Service Manual Kyocera KM-4800w;
This manual, Kyocera KM-4800w, is in the PDF format and have detailed Diagrams, pictures and full procedures to diagnose and repair your Kyocera KM-4800w copier.
You can print, zoom or read any diagram, picture or page from this Service Manual. Every chapter on this manual is fully detailed and contain all the simulation codes, trouble codes, maintenance procedures, reset procedures, diagnose procedures of Kyocera KM-4800w photocopier. You can find easily everything what do you need.
To see what contain, please read table of contents:

Chapter 1. INTRODUCTION
1. 1 Features
1. 2 Specifications
1. 2. 1 General
1. 2. 2 Printer part
1. 2. 3 Scanner part
1. 3 Appearance
1. 3. 1 Front
1. 3. 2 Rear
1. 4 Specifications for Originals
1. 4. 1 Original - Standard
1. 4. 2 Special Documents
1. 4. 3 "Do Not Scan" Originals
1. 5 Specifications for the Scan Original
1. 6 Specifications for the Printing Paper
1. 6. 1 Papers not available to use
1. 6. 2 Keeping the paper in the custody
1. 6. 3 Treatment against environmental condition

Chapter 2. INSTALLATION
2. 1 Installation Requirements
2. 2 Unpacking
2. 1 Unpacking
2. 2 Confirmation of Accessories
2. 3 Leveling the Machine
2. 4 Setup of the Roll Deck
2. 5 Setup of the Machine
2. 6 Installation of Accessories
2. 7 Turning on the Machine
2. 8 Initializing Scanner Unit
2. 9 Installation of Optional Licenses
2. 9. 1 Scan System 2 (for Scan to File)
2. 9. 2 UG-32 (for PDF printing)

Chapter 3. PRINT/SCAN PROCESS PAGE
3. 1 Print Process
3. 1. 1 Characteristic of toner
3. 1. 2 Each step of the print process
3. 1. 2. 1 Erasing (Removal of negative electric charges)
3. 1. 2 .2 Charge of Drum
3. 1. 2. 3 Exposure
3. 1. 2. 4 Development
3. 1. 2. 5 Transfer
3. 1. 2. 6 Separation
3. 1. 2. 7 Drum Cleaning (Removal of remained toner)
3. 1. 2. 8 Fusing
3. 1. 3 Controlling the movement of toner in the Developer Unit
3. 1. 4 Toner Collection Process
3. 1. 5 Density Compensation Process
3. 2 Scan Process
3. 2. 1 Data flow in scan and copy
3. 2. 2 Positioning process of Image Block

Chapter 4. ELECTRICAL PAGE
4. 1 General Information
4. 2 Electrical Components Location
4. 2. 1 Right side
4. 2. 2 Left side
4. 2. 3 Back side
4. 2. 4 Front side
4. 2. 5 LED Head Frame
4. 2. 6 Main Frame
4. 2. 7 Developer Unit
4. 2. 8 Fuser Unit
4. 2. 9 Roll Deck
4. 2.10 Cutter Unit
4. 2.11 Inner Transport Unit
4. 2.12 Scanner Unit
4. 3 Check & Adjustment of Analog Output from HV Power Supply
4. 3. 1 Situations necessary to check the analog output
4. 3. 2 Check & Adjustment of Analog Voltage to the Image Corona
4. 3. 3 Check & Adjustment of Analog Voltage to the Transfer Corona
4. 3. 4 Check & Adjustment of AC Component to the Separation Corona
4. 3. 5 Check & Adjustment of DC Component to the Separation Corona
4. 3. 6 Check & Adjustment of Negative Developer Bias to the Developer Roller
4. 3. 7 Check & Adjustment of Positive Developer Bias to the Developer Roller
4. 3. 8 Check & Adjustment of the Bias gap between Developer Roller and Regulation Roller
4. 3. 9 Check & Adjustment of Positive Cleaning Roller Bias (Print Cycle)
4. 3.10 Check & Adjustment of Negative Cleaning Roller Bias (Toner Collection Process)

Chapter 5. MECHANICAL PAGE
5. 1 Outer Covers
5. 1. 1 Removal of Side Covers
5. 1. 2 Removal of Cover 15
5. 1. 3 Removal of Cover 14
5. 2 Developer Unit
5. 2. 1 Removal of the Developer Unit
5. 2. 2 Replacement of Developer Unit Components
5. 2. 3 Replacement of Toner Supply Roller
5. 2. 4 Replacement of Screw Assy
5. 2. 5 Replacement of DC Motor
5. 2. 6 Replacement of Sensor (TLS1)
5. 2. 7 Adjustment of the space between gears (Necessary to adjust after replacing the Developer Unit)
5. 2. 8 Readjustment of the pressure of Regulation Roller
5. 3 Fuser Unit
5. 3. 1 Removal of the Fuser Unit
5. 3. 2 Replacement of Fuser Unit Components
5. 3. 3 Replacement of Roller Pressure
5. 3. 4 Replacement of Thermistors
5. 3. 5 Replacement of Thermostat
5. 3. 6 Replacement of Exit Sensor
5. 4 Roll Deck
5. 4. 1 Replacement of Cutter Assembly
5. 4. 2 Replacement of Clutches (CL3, CL4 & CL5) of Roll 1
5. 4. 3 Replacement of Clutches (CL6 & CL7) of Roll 2
5. 4. 4 Replacement of Timing Belt 633
5. 4. 5 Replacement of Timing Belt 453
5. 4. 6 Replacement of Timing Belt 330
5. 4. 7 Replacement of Sensors (PH6, PH7, PH9 PH12)
5. 4. 8 Replacement of Sensors (PH8)
5. 4. 9 Replacement of Sensors (PH10)
5. 4.10 Replacement of Dehumidify Heater (Roll 1)
5. 4.11 Replacement of Dehumidify Heater (Roll 2)
5. 4.12 Installation of Dehumidify Heater Kit (Option)
5. 4.12. 1 Installation of 1 Roll Dehumidify Kit
5. 4.12. 2 Installation of 2 Roll Dehumidify Kit
5. 4.13 Installation of Roll Deck 2 Kit (Option)
5. 5 Photoconductive Drum
5. 5. 1 Replacement of the Photoconductive Drum
5. 5. 2 How to fix the Aluminum Blocks
5. 5. 2. 1 Fixing Block with Drum Block Fix Tool
5. 5. 2. 2 Fixing Block by hand (w/o Drum Block Fix Tool)
5. 5. 3 Cleaning of Photoconductive Drum
5. 5. 4 Replacement of Belt 4
5. 6 LED Head
5. 6. 1 Replacement of the LED Head Unit
5. 6. 2 LED focus adjustment
5. 6. 2. 1 Check of the Test Pattern Image
5. 6. 2. 2 Positioning of the Aluminum Blocks
5. 6. 2. 3 Focus Adjustment with Spacers
5. 7 Image Corona
5. 7. 1 Removal of the Image Corona Unit
5. 7. 2 Replacement of the Corona Wire
5. 8 Transfer / Separation Corona
5. 8. 1 Removal of the Transfer / Separation Corona
5. 8. 2 Replacement of Corona Wires
5. 9 Engine Frame
5. 9. 1 Replacement of DC Motor (M4) and Developer Press Sensor (PH4)
5. 9. 2 Replacement of Manual Set Sensor (PH5) & Registration Sensor (PH1)
5. 9. 3 Replacement of Fans (BL5 & BL6)
5. 9. 4 Replacement of Blowers (BL3 & BL4)
5.10 Inner Transport Unit
5.10. 1 Removal of the Inner Transport Unit
5.10. 2 Replacement of Sensor (PH2) & Belt
5.11 Main Frame
5.11. 1 Replacement of DC Motors (M1, M2), Belt 8, Belt 9, Belt 7
5.11. 2 Replacement of Clutch (CL1)
5.11. 3 Replacement of Blower (BL7)
5.12 Scanner Unit
5.12. 1 Removal of the Scanner Unit
5.12. 2 Replacement of Belt
5.12. 3 Replacement of Motor Assy
5.12. 4 Replacement of Feed Roller
5.12. 5 Replacement of Pinch Roller Assy
5.12. 6 Replacement of Sensor
5.12. 7 Replacement of CIS
5.12. 8 Replacement of Scan Glass Assy
5.13 Optional Attachment
5.13. 1 Copy Tray Wide

Chapter 6. MAINTENANCE PAGE
6. 1 Recommended Periodical Replacement Parts
6. 2 Maintenance Period
6. 2. 1 Cleaning
6. 2. 2 Lubrication
6. 2. 2. 1 Driving Gears on Machine Frame
6. 2. 2. 2 Developer Unit
6. 2. 2. 3 Terminal Plates on Machine Frame
6. 3 Service Kit

Chapter 7. TROUBLESHOOTING PAGE
7. 1 Troubleshooting - Printer Errors
7. 1. 1 Countermeasures - Call Operator Errors
7. 1. 1. 1 Roll 2 Feeding Jam "Delay" (J-0101)
7. 1. 1. 2 Roll 1 Feeding Jam "Delay" (J-0102)
7. 1. 1. 3 Feeding Jam "Delay" (J-0103) & "Early" (J-0303)
7. 1. 1. 4 Reg. Jam "Delay" (J-0104), "Stay" (J-0204) "Early" (J-0304), "Remained" (J-1004)
7. 1. 1. 5 Internal Jam "Delay" (J-0106), "Stay" (J-0206) "Early" (J-0306), "Remained" (J-1006)
7. 1. 1. 6 Fuser Jam "Delay" (J-0107), "Stay" (J-0207) "Early" (J-0307), "Remained" (J-1007)
7. 1. 1. 7 Paper jam by opening the Roll Deck during printing (J-1100)
7. 1. 1. 8 Paper jam by opening the Exit Cover during printing (J-1200)
7. 1. 1. 9 Deck Open
7. 1. 1.10 Deck Jam
7. 1. 1.11 Manual Set NG
7. 1. 1.12 Toner Empty
7. 1. 1.13 The door opened during the print
7. 1. 1.14 Abnormal variation in cut length
7. 1. 2 Countermeasures - Call Service Errors
7. 1. 2. 1 Fuser Error (E-000, E-002 & E-004)
7. 1. 2. 2 Fuser Error (E-001)
7. 1. 2. 3 Fuser Error (E-003)
7. 1. 2. 4 Main Motor Error (E-010)
7. 1. 2. 5 Fuser Motor Error (E-011)
7. 1. 2. 6 Developer Press Motor Error (E-012)
7. 1. 2. 7 Counter Error (E-020)
7. 1. 2. 8 High Voltage Output Error (E-031, E-032 & E-033)
7. 1. 2. 9 Bias Output Error (E-034)
7. 1. 2.10 Cutter Error (E-040)
7. 1. 2.11 FPGA Error (E-050)
7. 1. 2.12 Developer Error (E-070)
7. 1. 2.13 Density Sensor Error (E-080)
7. 1. 2.14 Density Sensor Output Error (E-081)
7. 2 Troubleshooting - Image Quality Defects
7. 2. 1 Basic Image Adjustment
7. 2. 2 Countermeasures - Image Quality Defects
7. 2. 2. 1 Halftone is too light
7. 2. 2. 2 Halftone and solid black are too light
7. 2. 2. 3 The whole image is extremely light
7. 2. 2. 4 Density is uneven
7. 2. 2. 5 Totally appeared foggy image
7. 2. 2. 6 Foggy image or blurred black wide line (vertical)
7. 2. 2. 7 Clear black thin line (vertical)
7. 2. 2. 8 White line (Vertical)
7. 2. 2. 9 Void of image
7. 2. 2.10 Dirt on the back of the print
7. 2. 2.11 Defective fusing
7. 2. 2.12 Defective image placement, No Leading Edge
7. 2. 2.13 Jitter
7. 2. 2.14 Image looks not sharp
7. 2. 2.15 Uneven image density (vertical)
7. 2. 2.16 Completely white (No image)
7. 2. 2.17 Completely black
7. 2. 2.18 Crease of paper
7. 2. 2.19 Double image
7. 2. 2.20 Dirt on the print (Offset)
7. 2. 2.21 Image Void on Long Print without Crease
7. 2. 2.22 Crease on Long Print (and image void at a time)
7. 2. 3 Fuser Pressure Adjustment (NIP width check)
7. 3 Troubleshooting - Scanner Defects
7. 3. 1 Countermeasures - Scanner Operation
7. 3. 1. 1 Original can not be set (Scanner does not transport)
7. 3. 1. 2 Scanner does not start scanning from the original set position
7. 3. 1. 3 Original can not be set (Original feeding does not stop)
7. 3. 1. 4 Original is mis-fed
7. 3. 1. 5 Motor rotates endlessly at the time of turning on
7. 3. 1. 6 Scanner is not recognized
7. 3. 2 Countermeasures - scanner image quality
7. 3. 2. 1 Completely black
7. 3. 2. 2 Vertical black lines
7. 3. 2. 3 Vertical white lines
7. 3. 2. 4 Some image is lost at the boundary of Image Blocks
7. 3. 2. 5 Vertical image gap between Image Blocks
7. 3. 2. 6 Image quality is not good
7. 3. 2. 7 Density is different between left and right

Chapter 8. SERVICE MODE/UTILITY PAGE
8. 1 Outline of Service Mode
8. 1. 1 Entering Service Mode
8. 1. 2 Selecting each Sub Mode
8. 1. 3 Cancelling the Service Mode
8. 2 Signal Status Mode
8. 2. 1 Function
8. 2. 2 Indication and Operation
8. 2. 3 Device Signal List
8. 3 Information Mode
8. 3. 1 Function
8. 3. 2 Indication and Operation
8. 4 Device Operation Mode
8. 4. 1 Function
8. 4. 2 Indication and Operation
8. 5 Adjustment Mode
8. 5. 1 Function
8. 5. 2 Indication and Operation
8. 5. 3 Setting Item list
8. 5. 4 Explanation for each Setting Item
8. 5. 4. 1 Leading Registration (No. 000 & 001)
8. 5. 4. 2 Trailing Margin (No. 002 & 003)
8. 5. 4. 3 Side Margin (Left & Right) (No. 004)
8. 5. 4. 4 Side Registration (No. 005 to 007)
8. 5. 4. 5 LED Strobe Time for Main Pixel of each Block (No.008 to 010)
8. 5. 4. 6 LED Strobe Time for IST (Supplemental Pixel) of each Block (No.011 to 013)
8. 5. 4. 7 Horizontal Alignment of Pixels between Blocks (No.014 & 015)
8. 5. 4. 8 Cut Length 1 (length information provided) (No.016)
8. 5. 4. 9 Cut Length 2 (length information not provided) (No.017)
8. 5. 4.10 Cut Length 3 (Compensation of a long print) (No.018)
8. 5. 4.11 Leading Margin (No.019)
8. 5. 4.12 Cut Length 4 (Compensation of a long print) (No.020)
8. 5. 4.13 Developer Bias (No.022 to 027)
8. 5. 4.14 Developer Bias compensation - 1st Drum revolution (No.028)
8. 5. 4.15 Transfer Voltage (No.029 to 034)
8. 5. 4.16 Separation Corona ON Timing (No.035)
8. 5. 4.17 Transfer Corona ON Timing (No.037)
8. 5. 4.18 Transfer Corona OFF Timing (No.038)
8. 5. 4.19 Print - Fuser Temperature Center (No.039 to 044)
8. 5. 4.20 Fuser Temperature to start idling (No.045)
8. 5. 4.21 Warm Sleep - Fuser Temperature (No.046)
8. 5. 4.22 Fuser Temperature Control Range (No.048 & 049)
8. 5. 4.23 Reaction Time of Toner Supply Motor (No.050)
8. 5. 4.24 Toner Supply Motor ON Time (No.051)
8. 5. 4.25 Dot Enhancement Level (Dither) (No.052)
8. 5. 4.26 Feed Clutch (CL3) OFF time applied to long print (No.053 & 054)
8. 5. 4.27 Metric or Inch (No.055)
8. 5. 4.28 Language (No.056)
8. 5. 4.29 Interface Communication Setting (No.057)
8. 5. 4.30 Recognition of Roll Deck 2 (No.058)
8. 5. 4.31 Counter Value (No.059)
8. 5. 4.32 Maximum Length (No.060)
8. 5. 4.33 Stacking Device setting (No.061)
8. 5. 4.34 Down Sequence ON/OFF (No.062)
8. 5. 4.35 Cut Length 5 & 6 (Compensation for Tracing Paper / Film) (No. 063 & 064)
8. 5. 4.36 Drum Reverse Rotation Period (No.065)
8. 5. 4.37 Fuser Motor Reverse Setting (No.066)
8. 5. 4.38 Operation of Separation Lamp (No.067)
8. 5. 4.39 Compensation of Fuser Motor Speed for roll paper (Plain paper / A3, 12" & 11") (No.070 to 075, 678, 679)
8. 5. 4.40 Compensation of Fuser Motor Speed for roll paper (Tracing paper / A3, 12" & 11") (No.076 to 081, 680, 681)
8. 5. 4.41 Compensation of Fuser Motor Speed for roll paper (Film / A3, 12" & 11") (No.082 to 087, 682, 683)
8. 5. 4.42 Compensation of Fuser Motor Speed for roll paper (Special plain paper / A3, 12" & 11") (No.088 to 093, 684, 685)
8. 5. 4.43 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A3, 12" & 11") (No.094 to 099, 686, 687)
8. 5. 4.44 Compensation of Fuser Motor Speed for roll paper (Special film / A3, 12" & 11") (No.100 to 105, 688, 689)
8. 5. 4.45 Compensation of Fuser Motor Speed for roll paper (Plain paper / A2, 18" & 17") (No.106 to 111, 690, 691)
8. 5. 4.46 Compensation of Fuser Motor Speed for roll paper (Tracing paper / A2, 18" & 17") (No.112 to 117, 692, 693)
8. 5. 4.47 Compensation of Fuser Motor Speed for roll paper (Film / A2, 18" & 17") (No.118 to 123, 694, 695)
8. 5. 4.48 Compensation of Fuser Motor Speed for roll paper (Special plain paper / A2, 18" & 17") (No.124 to 129, 696, 697)
8. 5. 4.49 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A2, 18" & 17") (No.130 to 135, 698, 699)
8. 5. 4.50 Compensation of Fuser Motor Speed for roll paper (Special film / A2, 18" & 17") (No.136 to 141, 700, 701)
8. 5. 4.51 Compensation of Fuser Motor Speed for roll paper (Plain paper / A1, 24" & 22") (No.142 to 147, 702, 703)
8. 5. 4.52 Compensation of Fuser Motor Speed for roll paper (Tracing paper / A1, 24" & 22") (No.148 to 153, 704, 705)
8. 5. 4.53 Compensation of Fuser Motor Speed for roll paper (Film / A1, 24" & 22") (No.154 to 159, 706, 707)
8. 5. 4.54 Compensation of Fuser Motor Speed for roll paper (Special plain paper / A1, 24 & 22") (No.160 to 165, 708, 709)
8. 5. 4.55 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A1, 24" & 22") (No.166 to 171, 710, 711)
8. 5. 4.56 Compensation of Fuser Motor Speed for roll paper (Special film / A1, 24" & 22") (No.172 to 177, 712, 713)
8. 5. 4.57 Compensation of Fuser Motor Speed for roll paper (Plain paper / A0, 36" & 34") (No.178 to 183, 714, 715)
8. 5. 4.58 Compensation of Fuser Motor Speed for roll paper (Tracing paper / A0, 36" & 34") (No.184 to 189, 716, 717)
8. 5. 4.59 Compensation of Fuser Motor Speed for roll paper (Film / A0, 36" & 34") (No.190 to 195, 718, 719)
8. 5. 4.60 Compensation of Fuser Motor Speed for roll paper (Special plain paper / A0, 36 & 34") (No.196 to 201, 720, 721)
8. 5. 4.61 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / A0, 36" & 34" (No.202 to 207, 722, 723)
8. 5. 4.62 Compensation of Fuser Motor Speed for roll paper (Special film / A0, 36" & 34") (No.208 to 213, 724, 725)
8. 5. 4.63 Main Motor Speed (No.310 to 315)
8. 5. 4.64 Fuser Motor Speed (36"/34"/30"/24"/22"/A0/B1/A1) (No.316 to 321)
8. 5. 4.65 Separation Corona OFF Timing (No.322 to 327)
8. 5. 4.66 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A3, A2, 12", 11", 18" & 17") (No.328 to 333)
8. 5. 4.67 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A3, A2, 12", 11", 18" & 17") (No.334 to 339)
8. 5. 4.68 Compensation of Fuser Motor Speed for cut sheet paper (Film / A3, A2, 12", 11", 18" & 17") (No.340 to 345)
8. 5. 4.69 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A3, A2, 12", 11", 18" & 17") (No.346 to 351)
8. 5. 4.70 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A3, A2, 12", 11", 18" & 17") (No.352 to 357)
8. 5. 4.71 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A3, A2, 12", 11", 18" & 17") (No.358 to 363)
8. 5. 4.72 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A1, 24" & 22") (No.364 to 369)
8. 5. 4.73 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A1, 24" & 22") (No.370 to 375)
8. 5. 4.74 Compensation of Fuser Motor Speed for cut sheet paper (Film / A1, 24" & 22") (No.376 to 381)
8. 5. 4.75 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A1, 24" & 22") (No.382 to 387)
8. 5. 4.76 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A1, 24" & 22") (No.388 to 393)
8. 5. 4.77 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A1, 24" & 22") (No.394 to 399)
8. 5. 4.78 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / A0, 36" & 34") (No.400 to 405)
8. 5. 4.79 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / A0, 36" & 34") (No.406 to 411)
8. 5. 4.80 Compensation of Fuser Motor Speed for cut sheet paper (Film / A0, 36" & 34") (No.412 to 417)
8. 5. 4.81 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / A0, 36 & 34") (No.418 to 423)
8. 5. 4.82 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / A0, 36" & 34") (No.424 to 429)
8. 5. 4.83 Compensation of Fuser Motor Speed for cut sheet paper (Special film / A0, 36" & 34") (No.430 to 435)
8. 5. 4.84 Compensation of Fuser Motor Speed for roll paper (Plain paper / 30") (No.436 to 441, 726, 727)
8. 5. 4.85 Compensation of Fuser Motor Speed for roll paper (Tracing paper / 30") (No.442 to 447, 728, 729)
8. 5. 4.86 Compensation of Fuser Motor Speed for roll paper (Film / 30") (No.448 to 453, 730, 731)
8. 5. 4.87 Compensation of Fuser Motor Speed for roll paper (Special plain paper / 30") (No.454 to 459, 732, 733)
8. 5. 4.88 Compensation of Fuser Motor Speed for roll paper (Special tracing paper / 30") (No.460 to 465, 734, 735)
8. 5. 4.89 Compensation of Fuser Motor Speed for roll paper (Special film / 30") (No.466 to 471, 736, 737)
8. 5. 4.90 Compensation of Fuser Motor Speed for cut sheet paper (Plain paper / 30") (No.472 to 477)
8. 5. 4.91 Compensation of Fuser Motor Speed for cut sheet paper (Tracing paper / 30") (No.478 to 483)
8. 5. 4.92 Compensation of Fuser Motor Speed for cut sheet paper (Film / 30") (No.484 to 489)
8. 5. 4.93 Compensation of Fuser Motor Speed for cut sheet paper (Special plain paper / 30") (No.490 to 495)
8. 5. 4.94 Compensation of Fuser Motor Speed for cut sheet paper (Special tracing paper / 30") (No.496 to 501)
8. 5. 4.95 Compensation of Fuser Motor Speed for cut sheet paper (Special film / 30") (No.502 to 507)
8. 5. 4.96 Transfer Voltage applied at 100mm from trailing edge (Plain paper / Tracing paper / Film) (No.508 to 510)
8. 5. 4.97 Transfer Voltage applied at 70mm from trailing edge (Plain paper / Tracing paper / Film) (No.511 to 513)
8. 5. 4.98 Fuser Motor Speed applied at 30mm from trailing edge (Plain paper / Tracing paper / Film) (No.514 to 516)
8. 5. 4.99 Judgement Value for Additional Cut Length for Non-standard Size Prints (No.613 to 616)
8. 5. 4.100 Additional Cut Length for Non-standard Size Prints (No.617 to 620)
8. 5. 4.101 Toner Supply Roller Bias (No.621)
8. 5. 4.102 Regulation Bias (No.622)
8. 5. 4.103 Density Sensor Default Output (No.623)
8. 5. 4.104 Density Sensor Standard Output (No.624)
8. 5. 4.105 Print - Fuser Temperature Side (12"/11"/A3) (No.625 to 630)
8. 5. 4.106 Print - Fuser Temperature Side (18"/17"/15"/A2) (No.631 to 636)
8. 5. 4.107 Print - Fuser Temperature Side (24"/22"/A1) (No.637 to 642)
8. 5. 4.108 Print - Fuser Temperature Side (36"/34"/30"/A0/B1) (No.643 to 648)
8. 5. 4.109 Density Sensor Output Information (No.649)
8. 5. 4.110 Regulation Bias Increment for Auto Adjustment Level 2 & 3 (No.650)
8. 5. 4.111 Total Increment of Regulation Bias Adjustment (No.651)
8. 5. 4.112 Density Compensation ON/OFF (No.652)
8. 5. 4.113 Minimum Density (No.653)
8. 5. 4.114 Regulation Bias Maximum (No.654)
8. 5. 4.115 Density Measure Interval (No.655, 656)
8. 5. 4.116 Developer Bias Increment for Auto Adjustment Level 1 (No.657)
8. 5. 4.117 Ready - Fuser Temperature Center (No.660 to 665)
8. 5. 4.118 Ready - Fuser Temperature Side (No.666 to 671)
8. 5. 4.119 Fuser Motor Speed (18"/17"/15"/12"/11"/A2/A3) (No.672 to 677)
8. 5. 4.120 Compensation of Fuser Motor Speed 4 for Roll (No.678 to 736)
8. 5. 4.121 Standby - Fuser Temperature (No.738, 739)
8. 5. 4.122 Assist Fan Off Timing (No.740 to 742)
8. 5. 4.123 Fuser Motor Speed applied at 100mm from trailing edge (36"/34"/30"/A0/B1) (No.643 to 648)
8. 5. 4.124 Roll 2 Forward Standby ON/OFF (No.746)
8. 5. 4.125 Roll 2 Forward Standby Position Adjustment (No.747)
8. 5. 4.126 Roll 2 Rewind Timer (No. 748)
8. 5. 4.127 Tracing Mode (No. 749)
8. 5. 4.128 Roll 1 Setting Mode (No. 750)
8. 6 Running Mode
8. 6. 1 Function
8. 6. 2 Indication and Operation
8. 7 Jam/Error Mask Mode
8. 7. 1 Function
8. 7. 2 Indication and Operation
8. 8 Test Print Mode
8. 8. 1 Function
8. 8. 2 Indication and Operation
8. 8. 2. 1 Print Start Mode
8. 8. 2. 2 Deck Selection
8. 8. 2. 3 Paper Length
8. 8. 2. 4 Print Count
8. 8. 2. 5 Image Pattern
8. 8. 2. 6 Manual Type
8. 8. 2. 7 Manual Size
8. 8. 2. 8 Roll 1 Size
8. 8. 2. 9 Roll 1 Size Setting
8. 8. 2.10 Manual Size
8. 8. 2.11 Roll 2 Size Setting
8. 8. 2.12 Mirror
8. 8. 2.13 Nega/Posi
8. 8. 2.14 Scale
8. 9 Factory Adjustment Mode (Factory Use Only)
8. 9. 1 Function
8. 9. 2 Indication and Operation
8.10 Clear Mode
8.10. 1 Function
8.10. 2 Indication and Operation
8.10. 2. 1 RAM Clear Mode
8.10. 2. 2 Error Clear Mode
8.10. 2. 3 Jam History Clear Mode
8.10. 2. 4 Error History Clear Mode
8.10. 2. 5 Software Counter Setting Mode
8.10. 2. 6 Total Counter Setting Mode
8.10. 2. 7 Density Compensation Reset Mode
8.11 User Mode
8.11. 1 Construction of the User Mode
8.11. 2 Selecting each sub mode
8.11. 3 Status Indication (Normal Mode)
8.11. 4 Deck Information Mode
8.11. 4. 1 Function
8.11. 4. 2 Indication and Operation
8.11. 5 Setting Mode 1
8.11. 5. 1 Function
8.11. 5. 2 Indication and Operation
(1) Material setting
(2) Size setting
8.11. 6 Setting Mode 2
8.11. 6. 1 Function
8.11. 6. 2 Indication and Operation
(1) Selection of each Sub Mode
(2) ON / OFF setting of Warm Sleep Mode
(3) Timer setting of Warm Sleep Mode
(4) ON / OFF setting of Cold Sleep Mode
(5) Timer setting of Cold Sleep Mode
(6) ON / OFF setting of Auto Power OFF
(7) Timer setting of Auto Power OFF
(8) Transfer Assist setting
(9) Smoothing setting
(10) Dot Enhancement ON/OFF setting
(11) Full Image Mode setting
(12) Low Temperature Mode setting
8.11. 7 Command Mode
8.11. 7. 1 Function
8.11. 7. 2 Indication and Operation
8.12 Scanner Utility
8.12. 1 Installation
8.12. 1. 1 Installing USB Driver
8.12. 1. 2 Installing Scanner Utility
8.12. 2 Starting Scanner Utility
8.12. 3 Displaying Scanner Information
8.12. 4 Scanner Adjustment
8.12. 4. 1 Shading (Calibration)
8.12. 4. 2 Feed Distance (1:1)
8.12. 4. 3 Position (Stitching)
8.12. 5 Updating Scanner Firmware
8.13 Firmware Update (PW11620)

Chapter 9. APPENDIX

Number of pages: 744.
File Data

This file is sold by onedollar, an independent seller on Tradebit.

File Size 119 megabytes
File Type PDF
Our Reviews
© Tradebit 2004-2024
All files are property of their respective owners
Questions about this file? Contact onedollar
DMCA/Copyright or marketplace issues? Contact Tradebit