$29.00
Download NowSold by digibids on Tradebit
The world's largest download marketplace
3,254,090 satisfied buyers
The world's largest download marketplace
3,254,090 satisfied buyers
M38 1/4 Ton 4x4 Utility Truck, Maintenance Manual
This is a quality reprint of US Army Manual TM9 8912, M38 maintenance manual. Originally published in January of 1956. It is a later document as the M38 had been in service by this time for five years and for practical purposes replaced by the M38A1. The M38 is my favorite jeep and always will be. If it is one of yours and you are lucky enough to posses one, here is an excellent resource for it.
From the Manual:
1. Scope
a. These instructions are published for the use of personnel to whom this materiel is issued. They contain information on the operation and organizational maintenance of the materiel as well as descriptions of major units and their functions in relation to other components of the materiel.
b. The appendix contains a list of current references, including supply manuals, forms, technical manuals, and other available publications applicable to the materiel.
c. This manual differs from TM 9-804, September 1950, as indicated in (1 ), (2), and (3) below.
(1) Adds information on
(a) Plate showing "OFF" and "ON" positions under ignition switch, beginning with vehicle serial No. 26273.
(b) A changed submersible starter mounting, beginning with vehicle serial No. 53262.
(c) A submersible generator, beginning with vehicle serial No. 53262.
(d) A sealed or pressurized bell housing, beginning with vehicle serial No. 53262.
(e) A waterproof clutch linkage, beginning with vehicle serial No. 53262.
(f) A 1/8-inch hole in crankshaft pulley for timing purposes, beginning with vehicle serial No. 22296.
(g) Vent lines to bell housing, transfer case and transmission case, beginning with vehicle serial No. 53262.
(h) Decalcomania above deep water fording vent valve control, for locating bell housing drain plug and fording information, beginning with vehicle serial No. 53262.
(i)New engine rear plate for use with the changed starter mounting, beginning with vehicle serial No. 78513.
(j) Decalcomania on fuel tank cap, beginning with vehicle serial No. 14693.
(k) Distributor and voltage regulator harness assembly, beginning with vehicle serial No. 20600.
(l)Indicates different length of speedometer cables used.
(m) Cleaning of crankcase control valve and fuel filter element.
(n) Installation of oil filter flexible inlet line and carburetor to fuel pump line.
(o) Installation of thermostat housing retainer.
(p) Installation of polarizing bracket for trailer coupling connector receptacle.
(q) Replacement of old and new type stop light switches.
(r) Installation of front axle brake line clamps.
(2) Revises information on
(a) Light switch, beginning with vehicle serial No. 66736.
(b) Name, date, caution, and instruction plates.
(c) Alemite fittings, beginning with vehicle serial No. 28300.
(d) Instrument cluster, beginning with vehicle serial No. 65043.
(e) Gear oil specification, in lubrication order temperature range + 40 ° F. to -10° F., using GO 75 in place of GO 90.
(i) Forms, records, and reports.
(g) Table I, special tools and equipment for organizational maintenance.
(h) Circuit breaker, beginning with vehicle serial No. 65928.
(3) Deletes reference to cartridge-type oil filter which was used only on pilot models. Cuno oil filter was used in all production vehicles.
This is a Factory Service Manual in pdf format to study it on your PC or just print out the particular page or chapter you are working on, and not to worry about getting it dirty and oily.
File Format: PDF
Language: English
Compatible: All Versions of Windows & Mac
Requirements: Adobe PDF Reader /winzip
File Data
This file is sold by digibids, an independent seller on Tradebit.
| File Size | 22 megabytes |
| File Type | ZIP |