$14.95
Download NowSold by alps on Tradebit
The world's largest download marketplace
3,251,781 satisfied buyers
The world's largest download marketplace
3,251,781 satisfied buyers
Linde Electric Forklift Truck Type 336 Explosion Protected: E25, E30 Service Training Repair Manual
Model Covers:
E25
E30
Service Repair Manual Covers:
0 General
0.1 Instructions
0.2 Explosion protection measures on the vehicle
0.2.1 Battery
0.2.2 Electric installation
0.2.3 Tyres / Drivers seat
0.2.4 Dashboard
0.2.5 Instruments
0.2.6 Fork arms
0.3 Tests for explosion protected industrial trucks acc. to Elex-V as per P
0.4 Tests of explosion protected installations at three year intervals
0.5 Screw torque for pressure proofed housing covers
0.6 Special tools
1 Drive motor
1.1 Drive motor 80 V
1.1.1 Technical data
1.1.2 General
1.1.3 Inspection and replacement of carbon brushes in drive motors
1.1.4 Cleaning the drive motors
2 Drive - transmission
2.1 Disassembling the drive axle
2.2 Removal and assembly of the motor at the wheel drive unit
2.3 Assembling the drive axle
2.4 Replacing the speed sensor on the drive motor
3 Vehicle design
3.1 Drivers seat
3.1.1 Checking the leakage resistance of the drivers seat
3.1.2 Seat switch explosion protected
3.1.3 Removing and installing the seat switch
4 Steering system and wheels
4.1 Servostat
4.2 Curve sensors
4.2.1 Adjusting the curve sensors
4.2.2 Removing and installing a curve sensor
4.3 Drive wheels
4.3.1 Checking the leakage resistance of the drive wheels
5 Control elements
5.1 Travel control
5.1.1 Accelerator Sensor
5.1.2 Checking the output signals of the accelerator sensor in the intrinsically safe cir
5.1.3 Removing and installing the accelerator sensor
5.2 Brake control
5.2.1 Renew the brake Pads
5.2.2 Adjusting the foot brake
5.2.3 Adjusting the hand brake
6 Electrical system
6.1 Pressure resistant fully enclosed housing
6.1.1 Maintenance on pressure resistant housings
6.1.2 Control housing
6.1.3 Pressure resistant housing for Exciter resistor 1R2 (Up to 10.96)
6.1.4 Pressure resistant housing for voltage transformer
6.2 Checking the sealing function of PG-fittings
6.3 Checking condition and tight fit of electric cables
6.4 Checking the insulation resistance of the electrical system
6.5 Intrinsically safe electric circuits
6.5.1 Buffer amplifier, function and description
6.5.2 Internal circuit diagram of a buffer amplifier
6.5.3 Checking the function of the buffer amplifiers
6.5.4 Replacing the buffer amplifier
6.6 Function and description of the Zener barrier
6.6.1 Terminal designation on the Zener barrier
6.6.2 Internal circuit diagram of the Zener barrier
6.6.3 Checking the internal resistance of the Zener barriers
6.6.4 General function of the Zener diodes
6.6.5 Checking the output signals in the intrinsically safe circuit
6.7 Power supply
6.7.1 Monitoring unit 1V1 and release signal
6.8 Insulation monitoring 3V3 (Option)
6.8.1 Insulation monitoring (3V3) fault detection
6.8.2 Insulation monitoring 3V3 after 94/9 EG (ATEX 100)
6.8.3 Checking the insulation monitoring 3V3
6.8.4 Insulation monitoring 3V3 fault detection
6.9 Circuit diagrams up to 08/97
6.9.1 Main electric circuit for driving, lifting
6.9.2 Electric control circuit for driving
6.9.3 Intrinsically safe circuit - buffer amplifier and Zener barriers
6.9.4 Intrinsically safe circuit - carbon brush wear indicator
6.9.6 Auxiliary electrics - lighting and working head lights
6.9.7 Terminal strip X1 - not intrinsically safe circuits (up to 08/97)
6.9.8 Terminal strip X2 intrinsically safe circuits (up to 08/97)
6.10 Electric diagrams from 09/97
6.10.1 Main electric circuit for driving, lifting
6.10.2 Electric control circuit for driving
6.10.3 Intrinsically safe circuit - buffer amplifiers and Zener barriers
6.10.4 Intrinsically safe circuit - carbon brush wear indicator
6.10.5 Carbon brush monitoring
6.10.6 Auxiliary electrics - lighting and working head lights
6.10.7 Terminal strip X1 - Not intrinsically safe circuits (From 09/97)
6.10.8 Terminal strip X2 intrinsically safe circuits (from 09/97)
6.11 Circuit diagrams from 7/98
6.9.1 Main electric circuit for driving, lifting
6.11.2 Electric control circuit for driving
6.11.3 Intrinsically safe circuit - buffer amplifiers and Zener barriers
6.11.4 Intrinsically safe circuit - carbon brush wear indicator
6.11.5 Carbon brush monitoring
6.11.6 Auxiliary electrics - lighting and working head lights
6.11.7 Terminal strip X1 - not intrinsically safe circuits (from 07/98 w/o Atex)
6.11.8 Terminal strip X2 intrinsically safe circuits (from 07/98)
6.12 Circuit diagrams from 08/98 (94/9 EG)
6.12.1 Main electric circuit for driving, lifting
6.12.2 Electric control circuit for driving
6.12.3 Intrinsically safe circuit - Buffer amplifier and Zener barriers
6.12.4 Intrinsically safe circuit - Carbon brush wear indicator
6.12.5 Carbon brush monitoring
6.12.6 Auxiliary electrics - lighting and working head lights
6.12.7 Terminal strip X1 - Not intrinsically safe circuits (from 08/98 ATEX)
6.12.8 Terminal strip X2 intrinsically safe circuit (from 08/98 ATEX)
6.13 Illustration of components in pressure resistant housings
6.13.1 Pressure resistant control housing
6.14 Pressure resistant transformer housing
7 Hydraulic system
7.1 General
7.2 Pump motor
7.2.1 Technical Data
7.2.2 Removing and installing the pump motor
7.2.3 Changing the carbon brushes in the pump motor
7.2.4 Disassembly of the hydraulic pump
7.2.5 Speed sensor for Pump motor (2B8)
7.3 Displacement transducer
And More......
========================================
File Format: PDF, 164 pages
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader & WinZip
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are https://www.tradebit.com is great to have Linde Electric Forklift Truck Type 336 Explosion Protected: E25, E30 Service Repair Workshop Manual.
Thanks for visiting!
File Data
This file is sold by alps, an independent seller on Tradebit.
| File Size | 8 megabytes |
| File Type |